Certified Irrigation Designer Practice Exam

These questions are part of the practice quiz. Start practicing

• Multiconductor/Single Conductor: A cable assembly that contains multiple insulated conductors inside one jacket is called
• Which statement about shielding and bonding is true?
• What term refers to the vertical distance that influences pressure in hydraulic systems?
• A three-way valve has how many ports and what is its purpose?
• Matched precipitation rate refers to using emitters with similar application rates to achieve what?
• In irrigation hydraulics, which comparison expresses the relationship between flow rate and pressure characteristics?
• Which term refers to water produced when steam condenses in equipment or piping?
• Available pressure & volume is listed as a consideration when determining applying & implementing the water supply.
• Communication Wire: In an irrigation system, what is its primary use?
• Which item is listed as an accessory?
• In sensor categories, which option refers to monitoring electrical energy or supply for the system?
• What is a common method to protect underground irrigation control wires from moisture?
• Which joint is associated with a rubber O-ring as a common seal element?
• Which statement is true about centrifugal pumps?
• Which accessory enables remote control or status reporting for an irrigation system?
• What is the purpose of thrust blocking in pressurized piping?
• What do UL/CSA (ULc) codes indicate?
• Which concept is primarily concerned with minimizing water waste and protecting non-target areas by controlling where water goes?
• Flow Measurement: Which device is commonly used to measure flow in irrigation supply lines?
• Which term best describes a pump that can be submerged without damage?
• What is the function of a pressure regulating/sustaining valve?
• In pipe sizing, which two primary factors are typically considered to determine flow characteristics?
• What is the function of an air/vacuum relief in a piping system?
• Which combination is explicitly identified as part of understanding methods for pipe sizing?
• Which statement about an equipment grounding conductor is true?
• What term describes the loss of pressure due to friction as fluid moves through pipes?
• Which term refers to integrating irrigation controls with the pump for coordinated operation?
• What is the primary function of pumps in irrigation systems?
• Microsprays are connected to the irrigation tubing through a connector and spaghetti tubing and attached to risers that are either fixed or pop-up. Which option best describes this arrangement?
• Which item is included in the factors for determining proper low-volume application?
• Which of the following is a controller type that uses two wires in its conventional setup?
• Which term expresses the change in pressure per unit of elevation, often expressed as psi per foot?
• What is a typical purpose of using taller risers in sprinkler installations?
• Which characteristic of coaxial cables makes them suitable for EMI-prone environments?
• What statement best describes how a hydraulic valve is actuated compared to a manually operated valve?
• Which term describes the electrical power that is actually available to drive the pump after losses in the drive system?
• Which term describes wastewater that has been treated for reuse?
• Which statement best describes water quality effects on irrigation?
• What is a primary safety benefit of keeping low-voltage irrigation wiring separate from high-voltage power circuits?
• Normally Open/Normally Closed Valve: Which statement is true about normally open valves?
• The Rain Bird Drip System Operation Indicator Kit rises to indicate water flow when system pressure reaches approximately how many psi?
• Which statement about spray heads and zone placement is true?
• NPSH stands for Net Positive Suction Head Available. Which of the following best reflects this statement?
• What is dynamic pressure?
• Which component regulates the automatic operation and sequencing of a filtration system?
• Ductile iron pipe is commonly used for which of the following applications?
• Which term refers to drinking water fit for human consumption?
• What does a check valve do?
• What is a primary benefit of including pressure tanks in an irrigation system?
• Which term describes the condition in which all sprinkler heads within an irrigation zone apply water at the same rate?
• In a transformer, which winding is connected to the power source?
• A Water Quality Sensor is best described as:
• Which condition commonly causes cavitation in pump systems?
• Hydraulics (16%): In irrigation hydraulics, head loss in a pipe is primarily caused by what?
• What is the dynamic pressure equation?
• Which site-factor best supports maintaining uniform irrigation and reducing overspray?
• Ductile iron pipe is a direct development of which older pipe?
• Which device is used to seal and protect splices in irrigation wiring from moisture?
• Which of the following is included as an accessory?
• What is a common method to join irrigation conductors in outdoor installations?
• Which term describes routing electrical wires through protective conduits to protect them from damage?
• Which of the following is included as an accessory?
• What does the bypass switch do in an irrigation controller?
• Which term describes a conductor that is flexible and made of many strands?
• Which statement best describes a Weather/Soil-Moisture Based Controller?
• Which of the following is included as an accessory?
• Which hydraulic concept describes maintaining system pressure within a desired range?
• In irrigation planning, water allotments refer to:
• What describes voltage loss in an electrical circuit?
• Electromechanical control is commonly referred to as which term, reflecting its relay-based mechanism?
• Integration with irrigation controls allows pump operations to be coordinated with zone valves and schedules. Which statement best describes this integration?
• Which term describes a plan showing routing of conductors between devices and terminations?
• What feature allows disconnecting lines quickly without purging?
• In pipe sizing, which combination is used to determine the effects of flow?
• Which factor is related to the water supply in sprinkler spacing considerations?
• Which parameter is NOT typically measured by a water quality sensor?
• Which practice best minimizes the risk of stray voltage affecting irrigation valves?
• Sand Separator is a filtration device used in low-volume irrigation. Which action does it perform?
• Suction Lift Pump corresponds to which type?
• Which practice helps minimize electrical hazards by routing and securing conductors away from potential damage?
• Matched precipitation rate refers to sprinklers delivering what?
• Which adjustment is explicitly listed under sprinkler spacing options to account for environmental variability?
• Which sensor category would be used to measure water level?
• Which factor is most directly used to determine irrigation zoning in a site with varying microclimates?
• Which feature of the hydrometer valve provides quick acting and positive opening and closing?
• Which item is NOT typically considered a valve accessory component?
• Which term describes a set of conductors within a single outer jacket used for multiple signals?
• Which material is commonly used for drip irrigation pipe?
• Which term represents the rate at which fluid moves through a pipe?
• Which sensor is described as a general term for multiple sensors measuring parameters such as pH and chlorine?
• What is the function of an air/vacuum relief valve?
• Between direct burial and conduit protection, which is generally preferred for durability and safety?
• Which statement correctly describes BHP and WHP in pump systems?
• Which sensor detects the amount of water vapor in air to support greenhouse plant growth?
• In drip irrigation, emitters are the end devices that what?
• Pressure tanks are typically used in conjunction with which type of water source?
• Which term refers to connectors used to join wires in an irrigation control system?
• Which term defines the pressure head available at the pump suction to prevent cavitation?
• Which component is used to join sections and permit disassembly for valve servicing?
• Which combination of devices would you expect downstream of a pump to control pressure and protect the system from surges?
• Which term governs legal authorization and regulatory compliance for water use in irrigation projects?
• What is the primary function of a check valve in an irrigation sprinkler system?
• Which medium is best suited for high data rate local area networks?
• What is the primary purpose of a Control Wiring Plan?
• In irrigation design, why is it essential to locate utilities before trenching?
• Which statement about the routing of cables to minimize interference is true?
• Scheduling Codes are used to ...
• Which factor has the greatest impact on voltage drop in irrigation circuits?
• Which sensor is designed to measure the height of water in a tank or reservoir?
• Which phrase represents the concept of adjusting irrigation design to match site conditions and intended use?
• Which filtration type relies on centrifugal force to separate solids from liquids?
• Which sensor is used to monitor soil moisture to aid water scheduling?
• Microclimates affect irrigation scheduling because they cause differences in:
• Wire Sizes: In North American practice, wire sizes are commonly specified using which standard?
• Which water source is water from precipitation events that can be captured and reused for irrigation?
• Which is a drawback of copper piping?
• What term describes the transient pressure rise in piping due to sudden changes in flow?
• What is a true statement about grounding and bonding in isolated wire paths for irrigation systems?
• Which sensor category would typically provide data on rainfall?
• Which pump type is typically used when the suction side is below the water source and the unit must be submerged?
• Which term refers to the speed at which a fluid moves?
• What is the primary purpose of codes in irrigation installation?
• In irrigation electrical design, which concept is referred to as 'Primary & Secondary Grounding'?
• Cable Construction: For frequent bending and vibration in irrigation installations, which wire type is best suited?
• Which accessory is used to draw water from an external source into the pump system?
• Which type of filtration uses granular media such as sand or anthracite to remove particulates?
• Polyethylene drip supply lines can be buried but are more often laid above ground. Which statement is true?
• How do dynamic and static pressure differ in a pressurized irrigation system?
• Which term describes condensate produced when steam is cooled and condenses?
• What device provides a master valve, water meter and flow sensor in a single unit for high-pressure remote applications?
• For trees, shrubs and native plants with wide and/or random spacing requirements, which irrigation method is the perfect alternative?
• What is the common voltage for the majority of irrigation solenoid control valves?
• Runoff considerations in sprinkler spacing aim to prevent water from doing what?
• Multistrand/Solid Core Wire: Which type offers greater flexibility for buried irrigation installations?
• In a pneumatic valve, what mechanism causes actuation as air pressure increases?
• During idle operation, what keeps the valve shut?
• What term refers to the part of the water cycle where an excess of water runs off the soil and eventually reaches rivers, lakes, and oceans?
• Which factor determines the required conductor size for a valve coil in an irrigation circuit?
• What voltage is typically used to operate an electric irrigation valve solenoid?
• Which sensor would help determine soil moisture content to schedule watering?
• What is the typical manufacturing method for ductile iron pipe?
• A flood-suction pump is typically used when which condition applies?
• Which of the following is a soil factor affecting infiltration in irrigation design?
• What is the primary benefit of using a Variable Frequency Drive in pump control?
• Conductor Color Coding: In typical electrical wiring, which color is commonly used to indicate a neutral conductor?
• From the listed controller accessories, which item provides protection against voltage surges?
• What is the "water window" in irrigation planning?
• Matched Precipitation Rate implies what about sprinkler heads within a zone?
• Elevation affects irrigation design primarily by influencing:
• Two-Wire: In irrigation control systems, what does a two-wire scheme typically use?
• Which filter is designed to remove fine particles using stacked discs and is often self-cleaning?
• Condensate is listed as a water supply type. Which option correctly identifies this category?
• What term ensures consistent pressure in irrigation design?
• Which joint uses heat to join or fuse materials?
• Cycle and soak scheduling is primarily used to:
• Which of the following is a drawback of PVC piping for drinking water?
• What does P.O.C. Codes refer to in this context?
• What is the purpose of quick coupling valve?
• What is the purpose of strain relief in electrical connections?
• What is a typical consequence of neglecting thrust blocking and proper placement?
• Which sensor produces an electrical signal related to temperature?
• Cast iron pipes were typically used for which type of piping?
• Which item is explicitly listed as a low volume irrigation accessory alongside valves, filters, and pressure regulators?
• Which option best describes the part of wiring standards that governs color codes and sizing?
• What does a control wiring plan illustrate?
• Which parameter describes the resistance to flow in a pipe due to roughness and turbulence?
• What is the recommended method for protecting splices in buried irrigation control wiring?
• Which accessory is used to monitor flow and control pump operation?
• Which organization listing is represented by UL/CSA (ULc) for electrical equipment?
• Which description best describes a Submersible Pump?
• Management Allowed Depletion (MAD) is defined as what?
• Which type of filter commonly requires backwashing to restore flow capacity?
• Which controller type is commonly used for centralized management of irrigation across many zones?
• Which term describes water that flows in natural channels and can serve as a source for irrigation?
• Which concept is essential to manage seasonal shutdowns and startup procedures for irrigation systems?
• Which of the following is a sensor category used in irrigation systems?
• Which factors are typically considered under Understanding & Mitigating Environmental Conditions?
• Which sensor can use differential pressure to obtain level and flow measurements?
• When should angle valves be preferred over standard globe valves?
• Hydrozones are ...
• Compared to fixed spray nozzles, multistream multitrajectory rotaries:
• An air relief valve is designed to discharge large volumes of air during filling and pressurizing, and to admit air when draining, but cannot ...?
• Which device allows your irrigation timer to communicate with the pump?
• In irrigation design, which term governs installation standards and safety requirements?
• Wells are listed as a water supply type. Which option correctly describes this?
• Adjusting the VAN nozzle in a drip system is used to create what visual cue that the system is running?
• Which factors are considered when determining equipment location in an irrigation system?
• Which valve type is designed to vent air and prevent vacuum in irrigation lines?
• Which equation expresses Ohm's Law?
• The phrase Rectangular-Triangular-Single Row is used to describe which design element?
• Which statement about Determining Proper Low Volume Application is true?
• What defines a Mechanical Joint in piping connections?
• What is a key moisture-protection practice for underground irrigation wiring?
• Rainwater is included among the water supply types. Which statement is correct?
• Which low volume irrigation method is particularly popular for nurseries due to its moisture-delivery characteristics?
• Which valve accessory component is used to establish electrical safety by connecting equipment to earth?
• Which filter type uses stacked discs with narrow gaps to remove particles?
• Cycle & Soak is an irrigation scheduling method designed to...
• Which item is NOT listed as an accessory?
• Which device actively measures water flow through a piping system and reports its data to the computerized central control system?
• In cabling, what does 'Plenum' designation indicate?
• Which sensor would most directly help reduce water use by sensing rainfall and deactivating irrigation?
• Which factor defines how deep irrigation water should be applied to reach the plant root zone?
• Risers/extensions in irrigation systems perform which of the following?
• Which joint uses solvent cement to weld PVC or ABS plastic pipes?
• Flow and pressure start concepts involve starting a pump based on certain conditions. Which statement is most accurate?
• What is the purpose of pressure regulation in irrigation piping?
• What is the role of conduit in irrigation valve wiring?
• Which term denotes water resulting from precipitation that is collected for reuse?
• Which water type is treated to be suitable for drinking?
• Which items are considered when evaluating irrigation system power supplies?
• What is a primary benefit of using point source drip in sparsely planted landscapes?
• In a step-down transformer, which statement describes the primary winding?
• Which filter type is designed to automatically flush and remove debris from the flow path?
• What is the Scheduling Multiplier used for in irrigation scheduling?
• Which concept accounts for the amount of fluid stored in a system?
• Which concept is the pressure present when a fluid is at rest?
• Which set of factors is used to determine proper low-volume application?
• Effluent Guidelines are national regulatory standards for wastewater discharge to surface waters and municipal treatment plants. Which agency issues these regulations?
• What is the primary purpose of a valve boxes?
• A pneumatic valve is powered by what?
• Which of the following is NOT a listed controller type?
• Which of the following are typical pump suction configurations?
• In a power transformer, which statement about the primary winding is accurate?
• What does Distribution Uniformity measure in an irrigation system?
• Which valve accessory component supplies electrical power to field devices?
• Which pump is described as a turbine pump close-coupled to a water-tight electric motor, eliminating the long drive shaft and bearing retainers?
• Which concept refers to devices or practices used to maintain a constant pressure within an irrigation distribution system?
• Which statement best defines static pressure?
• Which pump type operates while fully submerged in the fluid being pumped?
• What is the approximate inner diameter of ½ inch mainline poly tubing?
• Which term describes a device that protects irrigation equipment by maintaining a steady electrical reference?
• Which feature does an angle valve have that creates a 90-degree angle between inlet and outlet connections?
• Which term denotes the protective insulating layer around a conductor?
• Which design consideration relates to reducing audible disruption from equipment?
• Which term relates to the quality standards of the water supply?
• Which valve type is used to regulate or sustain pressure in an irrigation system?
• Whose recommendations are considered for sprinkler spacing as per the notes?
• What is the primary purpose of isolating wire paths in an irrigation system?
• Which device listed among valve types is used to measure the density of liquids and is included in the valve types list?
• Which component distributes water to multiple filter housings in a filtration system?
• Line Source emitters use a twin-wall tubing with two pipe chambers. Which statement is true about the larger inner chamber?
• What is a major cost consideration when designing irrigation zones?
• Which sensor's purpose is to sense the surrounding medium pressure?
• Which statement about flower beds is true?
• Which of the following items are considered fittings in a piping system?
• Which of the following is included as an accessory?
• Storage/impoundment in irrigation design serves to:
• What primarily differentiates a hydraulic valve from a pneumatic valve?
• Overspray in an irrigation system is best described as water that lands on which areas?
• Which concept involves protecting wires and electrical connections by routing them through protective conduits or sleeves?
• In a vertical turbine pump, what happens to water when it reaches the rotating impellers?
• Which term refers to natural water sources such as rivers, lakes, or streams that require treatment before use?
• Which term describes a surface water source derived from natural streams used for irrigation?
• Topography influences irrigation design by:
• Microsprays are a cross between surface spray and drip irrigation. They are well suited for irrigating which of the following?
• Which concept relates to pressure caused by the motion of fluid, not by its static pressure?
• Stormwater is listed as a water supply type. Which option correctly identifies this category?
• What is the purpose of a pressure relief valve in an irrigation system?
• A pressure sustaining valve is often used downstream of filter stations to provide adequate backflush pressure. Where is it typically installed?
• What is the role of a Pressure Regulating Module in an irrigation system?
• What is the primary purpose of insulation around a conductor in electrical wiring?
• Which item is listed under weather influences on irrigation planning?
• Streams are listed as a water supply type. Which option correctly identifies this category?
• Media filtration solutions can filter from which range?
• Which statement best describes the purpose of storage/impoundment in irrigation systems?
• Which term describes treated wastewater that is reused in irrigation or other industrial processes?
• What is the purpose of color coding in irrigation wiring?
• Which sensor category would be used to monitor soil moisture?
• Which irrigation planning approach uses weather data, soil moisture, and plant water use to determine irrigation needs?
• Which joint is described as the most permanent joint type for waste pipes?
• Site Use refers to ...
• Which statement best describes spray heads?
• What is the goal of Wire Path Routing & Separation?
• Which term refers to the standards and regulations governing wire sizes and color codes in electrical installations?
• Which configuration best embodies wire path isolation in an irrigation installation?
• Spray heads typically discharge water compared to rotors by:
• Which statement about cables installed in plenum spaces is true?
• Pressure regulators help prevent leaks, emitter blowouts, premature system damage, and irregular water application. Which of the following best describes their primary purpose?
• Which filter is primarily used to disinfect water rather than remove particulates?
• Which term describes the periodic discharge used to reduce mineral buildup in irrigation or process systems?
• Which item is essential for establishing a reliable ground connection for electrical safety in irrigation installations?
• What does NPSH stand for?
• What characteristic defines the graphite within ductile iron?
• What is a major reason PEX should not be used outdoors?
• In a pumping system, what is the role of suction and discharge piping?
• Line Source Drip is best described as which configuration?
• Which statement best defines potable water as used in irrigation design standards?
• In an irrigation design, pressure losses due to head are accounted for by subtracting them from which value to determine if there is adequate pressure to raise water to the required height?
• What does polarity refer to in electrical circuits?
• Which component distributes water to multiple filtration stages or housings?
• Which statement about reclaimed water is supported by the material?
• Which sensor automatically deactivates irrigation to save water?
• Which principle about cable layout helps minimize interference in mixed-signal runs?
• Which component is used to connect two pipe sections and allow disassembly for maintenance without leaking?
• Where are check valve components typically located in a system that uses a check valve?
• Which device automates the on/off operation of irrigation valves?
• What is the purpose of a pressure regulator in irrigation?
• What is the primary benefit of swing assemblies over traditional rigid risers?
• A self-cleaning filtration system is designed to automatically flush out debris.
• Which phrase best describes velocity in words according to the material?
• Which grounding practice protects irrigation equipment from fault conditions?
• Which maintenance activity involves regular checks and servicing of irrigation components?
• What is the purpose of a strainer in irrigation piping?
• Which term represents a category of scheduling approaches including moisture-based, base schedule, water budget, and synthetic turf?
• What is the primary function of irrigation valves?
• What is a key benefit of using an irrigation controller with solenoid valves?
• The description 'A pump having a turbine and motor that can be submerged without damage' describes which pump type?
• To ensure reliability, what term describes the periodic checks and servicing intervals for irrigation hardware such as valves and drains?
• Where is a pressure relief valve typically mounted in an irrigation system?
• Which controller type serves as a central hub for multiple irrigation zones?
• Elevation is explicitly listed as a consideration when determining applying & implementing the water supply.
• In a drip irrigation emitter color code, which color corresponds to 2 gph?
• Blowdown is listed as a water supply type. Which option correctly identifies this category?
• Which of the following is included as an accessory?
• What is the electrical load in a circuit?
• Types (moisture based, base schedule, water budget, synthetic turf) refer to which irrigation scheduling approach?
• When electrical signal is sent to an irrigation valve solenoid, which occurs?
• Compared with PVC, HDPE piping is generally:
• What do pump performance curves primarily illustrate?
• Which pump type is described as drawing water by suction without requiring the suction supply to be pressurized?
• What is the equation for velocity provided?
• Which term refers to collecting and utilizing rainfall or runoff for use?
• Which statement best describes hydraulics in irrigation design?
• What is the primary function of a UV filter in irrigation water treatment?
• Which communication medium provides EMI protection through shielding?
• What is a relay in an irrigation controller circuit?
• Water Allotments are defined as a defined allocation of water volume or time per zone or period. Which term matches this concept?
• Which device is used to separate sections of the mainline to isolate downstream segments for repair?
• Which of the following reflects best practice for separate paths in an irrigation installation?
• PVC pipes have a smooth inner lining that provides what benefit?
• Which item is included as an accessory?
• Which statement best describes rotors relative to spray heads?
• In drip irrigation, which category represents emitters that discharge water at a single point?
• Why are codes important in placing irrigation equipment?
• In furrow irrigation, surge irrigation serves what purpose?
• Multiple points of connection are used to:
• What is the purpose of strain relief on irrigation valve wiring entering the valve body?
• Which water type generally comprises treated wastewater that may be reused?
• In the described submersible pump arrangement, where does water enter the pump?
• Which term refers to wastewater from domestic sources that is commonly reused for irrigation after treatment?
• Which component connects the pump to the supply source and to the field distribution network?
• What is the most likely outcome when wire path isolation is properly implemented?
• Before trenching for irrigation lines, which consideration is important regarding utilities?
• What does 'looped mains' describe in an irrigation piping system?
• What visual signal indicates the drip system has reached 20 psi and water flow when using a status indicator?
• Which valve accessory component is primarily used to record data from sensors?
• Which valve accessory component provides physical support for sensors?
• Water Window is defined as ...
• Which type of irrigation controller is defined by electro-mechanical control using relays, timers, and counters wired together on an enclosure panel?
• What is the primary function of a booster pump?
• Which scheduling type bases irrigation on soil moisture sensor readings?
• What regulatory factor must be addressed before installing irrigation pumping equipment?
• Which option is not a standard pump type mentioned?
• Which valve accessory is specifically designed to label components in an irrigation system?
• A design approach involving 'like equipment' refers to grouping equipment based on:
• Which item is not typically part of pump sizing?
• Which filtration option is best suited for removing very fine particulates before disinfection?
• A connector wire is typically used to ...
• When selecting irrigation system equipment, which factors are essential to evaluate?
• Which approach supports minimizing electrical interference between irrigation controllers and other electrical equipment?
• Which document shows how conductors are routed between devices and terminations?
• How many components are listed under Accessories?
• Which elements are included in a proper irrigation valve wiring installation?
• What is a typical operating range for rotor heads?
• Which concept focuses on preparing the system for the off-season by removing water and protecting components from freezing?
• What is a key consideration when designing a layout for irrigation wiring to ensure reliability?
• Which detects the amount of water vapor in air in greenhouse, to make sure plants grow well?
• Which sensor category would be used to monitor water quality?
• Which statement best defines nonpotable water?
• Which accessory helps stabilize power and reduce electrical noise to the controller?
• Which spacing configurations are listed as options for sprinkler spacing patterns?
• NPT is the standard pipe thread used in the U.S. for pipe fittings. Which joint type uses this standard?
• Which filter type uses a semi-permeable membrane to remove dissolved substances from water?
• What is a Y Strainer used for in irrigation piping?
• Which PEX color is typically used for hot water supply?
• Which item is NOT listed as a valve accessory?
• Which term describes a valve that can divert flow among three ports?
• Which PEX color is typically used for cold water supply?
• Which accessory provides a protective enclosure for the controller?
• What is a feature of some electric valves regarding manual operation?
• Lakes/Ponds are listed as a water supply type. Which option correctly characterizes this category?
• Multistream multitrajectory rotary sprinklers:
• Which instrument monitors the moisture content in the soil to assist in water scheduling?
• Which device is primarily used to relieve pressure and drain water from irrigation lines during service?
• Which term describes the condition where all sprinkler heads within the same irrigation zone apply water at the same rate?
• In irrigation wiring color coding, what does a white wire typically represent?
• Which accessory creates a reliable electrical path to ground for safety?
• Which valve accessory component provides environmental protection for sensors and electronics?
• What is a best practice for field connections in an irrigation system?
• Which item is included and relates to fluid path management?
• Which term refers to collecting and using water from precipitation or runoff?
• Which term describes water that has been treated for reuse in non-potable applications such as irrigation?
• Which of the following is an example of a valve accessory?
• Which item is both a listed accessory component and a term describing housing equipment?
• Which item is designed to be used with a timer to automate an irrigation system?
• Point of Connection: In an irrigation system, what is generally defined as the point of connection?
• When planning a zone layout, which is a primary objective?
• Soil conductivity is defined as which of the following?
• Where is a pressure sustaining valve typically installed?
• Cycle & Soak is used to...
• Why are rotor heads often preferred for sloped turf areas?
• What does precipitation rate specify in sprinkler design?
• Which of the following is NOT a soil factor listed?
• Which pump type is a modified centrifugal pump capable of drawing water from streams, ponds, and wells via suction?
• Which component is specifically used to prevent the pump from losing prime when pumping from a well?
• What functions are integrated in a hydrometer valve?
• Hydrozone categories include three main groups. Which option is NOT one of those groups?
• MAD is best described as ...
• Which statement best describes a Water Quality Sensor?
• Which water supply type would be most appropriate for collecting precipitation and storing it for later use?
• Which water source refers to water collected from precipitation and stored for later use in irrigation?
• Which of the following is a layout determination?
• Which enclosure feature protects irrigation electrical components from weather and moisture?
• Flanged joints are formed by bolting two flanges together with what between them to provide a seal?
• Which statement best reflects the purpose of grounding in electrical systems?
• Which medium is commonly used for legacy industrial networks and uses coaxial conductors?
• Which term refers to a simple control circuit that uses two conductors?
• Which valve styles are available as automatic valves?
• Which factor is critical to consider for sprinkler spacing and nozzle selection due to outdoor conditions?
• Which parameter describes the change in elevation across the irrigation field and affects head pressure?
• Which sensor provides an electrical signal related to its temperature?
• Which statement best describes a twisted pair in wiring?
• Which statement best describes surge or water hammer in piping?
• What is the purpose of color coding in control wiring?
• Equipment Location: Which factors influence the location of irrigation equipment such as valves and controllers?
• Pipe Sizing: Which factors are typically considered when sizing irrigation pipe?
• Which term refers to water that has been treated and reused for irrigation or other purposes?
• Water cannons:
• Which medium is commonly used for Ethernet networks?
• Mats are lightweight, mildew-resistant fabric designed to absorb water and then deliver it to the plants placed on the mat. Which statement best describes their use?
• Gray Water is listed as a water supply type. Which option correctly identifies this category?
• Which valve accessory component provides the source of electrical power to field devices?
• Cost is a factor in determining applying & implementing the water supply.
• Which concept is a key consideration in establishing proper pump selection and application?
• Which instrument is used to measure electrical resistance?
• What percentage is assigned to Layout in these notes?
• What is the primary purpose of voltage drop calculations in irrigation wiring design?
• Which factors determine the required wire size for control circuits?
• Which piping arrangement helps maintain pressure stability by creating a looped circuit?
• Determining proper zoning typically involves consideration of:
• In a typical electrical installation, to which point is the equipment grounding conductor connected on equipment?
• To minimize voltage induction from nearby power lines, which routing is best?
• Which option best describes conductors suitable for outdoor underground irrigation wiring?
• Which term describes regulatory limitations on when or how irrigation may occur?
• Which device is used to stop water flow at a zone or circuit level within a valve box?
• How does topography affect irrigation system design?
• Which conductor material is standard for irrigation wiring that runs underground?
• Which of the following is a listed controller type?
• Which statement determines the required conductor size for a valve coil?
• Why should control wiring be routed separately from power wiring?
• Which term describes water that naturally occurs in streams and rivers and can be used for irrigation?
• Which combination represents the two core components of pipe sizing methods?
• What best defines impedance in an alternating current circuit?
• Which measures wind speed and shuts the system off at a pre-set wind speed?
• Which sensor category would monitor environmental conditions such as wind and precipitation, often via an integrated device?
• Approximately what fraction of the moisture from the top quarter of the root zone is available to plants?
• What is the primary function of a pressure sustaining valve in an irrigation system?
• Wire Codes: Wire codes typically convey which information?
• What is the primary function of an air/vacuum relief valve in irrigation piping?
• Which term describes sensors that communicate data through either wired or wireless methods?
• Which component is used to shift a low-current control signal to switch a higher-current circuit while providing isolation?
• Which filtration device relies on centrifugal force to separate solids from liquids?
• Which term describes the hydraulic power delivered by the pump?
• Which factor should be considered when selecting components for an irrigation pump and piping?
• Which sensor measures wind speed to shut off irrigation?
• Why should suction piping be designed to minimize friction losses and avoid air pockets?
• Which property is true for Polyethylene (PE) pipe used in irrigation?
• In irrigation scheduling, what does Management Allowed Depletion (MAD) refer to?
• Which statement about maintenance is true?
• Which statement best describes GPM vs PSI?
• Disc filtration solutions can filter at the range of which micron values?
• What is the purpose of grounding in an irrigation electrical system?
• If you use different manufacturers for your controller and valves, what should you do?
• Screen filtration solutions can filter from which range?
• Which device is used to control a high-current circuit with a low-current control signal?
• Which topic concerns calculating the appropriate pipe diameter to achieve desired flow with acceptable velocity?
• Which pump type is used to pump from reservoirs, lakes, streams and shallow wells, and can serve as booster pumps in irrigation pipelines?
• Which valve accessory component is used to store and retrieve sensor data for later analysis?
• What does Prefabricated vs Site Built Pump refer to?
• Which pipe is replacing traditional copper and galvanized steel as water supply lines?
• Available pressure and volume considerations are important for planning: which statement is true?
• What device is used to isolate the water supply on the mainline during maintenance?
• Which statement describes alternating current?
• Where is the recommended location for the pump in a typical irrigation system?
• Line Source Drip emitters are used when plants are closely spaced within a row, with the rows separated several feet apart. Which irrigation category best matches this description?
• Which statement about shielding in cables is true?
• Which term describes a conductor that is solid and has no strands?
• Which regulatory item is listed among sprinkler spacing considerations?
• What is a manual valve?
• What is the friction loss formula given in the material?
• Which statement best describes the foot valve in a pumping system?
• Which valve accessory component is used to physically position equipment?
• Which concept improves reliability of control networks by reducing single points of failure?
• Which control device varies the speed of the pump motor?
• Which factor primarily determines how deep supply lines should be buried in a drip irrigation system?
• Which medium is commonly used for short-range simple control networks within a building?
• Hydrozones group plants with similar water needs to?
• Which component is used to improve electrical power quality provided to irrigation controllers?
• Which sensor can use differential pressure to obtain level and flow measurements?
• Which guideline should be consulted when selecting sprinkler and emitter components to ensure compatibility with the system?
• For small areas 5-15 feet, typical spray head configuration uses:
• When selecting emitters for a drip system, water quality is a factor to consider which statement is true?
• Which of the following is listed as a valve accessory?
• Which statement about polarity is correct for irrigation control circuits?
• Suction lift describes which pump arrangement?
• What is the function of pressure regulators in an irrigation system?
• Which filtration method removes dissolved ions and requires pressure to pass water through a semi-permeable membrane?
• Which item is NOT a listed consideration for determining proper low-volume application?
• Which activity is essential for preserving irrigation equipment during the off-season?
• What is the purpose of weather sensors in irrigation control?
• Flow cavitation is primarily caused by what condition?
• Which item allows disassembly of piping joints without causing leaks and is used in maintenance access points?
• Which term refers to groundwater extraction from underground reservoirs using drilling?
• In a typical irrigation controller installation, why is conduit recommended for the low-voltage wiring between the controller and valves?
• Which filter type uses a mesh or screen to remove particles from irrigation water?
• What is the purpose of electrical grounding in irrigation systems?
• Which item is explicitly listed as a controller accessory?
• What best defines hydrozones in irrigation design?
• Which type of controller is designed to be managed remotely over the internet?
• Overspray considerations include which areas?
• Which concept is the path that determines the limiting condition for system performance?
• Which centrifugal pump must be primed before operation?
• Which device provides automatic drainage of collected debris from filter housings?